RRD material is the best MX specific decal product out. Made with our easy to install Air Escape material to help with bubble free decals. 

1) Line up the bolt hole and the back corner.
2) Squeegee the red line starting from the middle and working out both ends.
3) Work your way down and split any wrinkles in half going out the ends.
4) Work your way to the bottom, go slow work bubbles out.
5) Go back to middle start working upward, again work wrinkles out the ends.
6) Work and remaining wrinkles and bubbles out the top.
7) Chrome material has a lower bond and plastic prep is critical.
8) Flo prints have limited life treat with 303 Protectant.  You can find it at Autozone.

Make sure your hands are clean. Remove mold release agents off your plastic before installing. Acetone
works best.
Brand new plastic is smooth but will have oily film from mold release from the factory. For super bonding
effect wave a propane torch lightly over the plastic. Just a quick pass, you should see the mold release evaporate off.
then clean again with acetone. Careful not to discolor the plastic. 21mil----warm graphic and plastic with hair dryer
before installing. For wet application (not recommended) we suggest mixing a  bottle of water with one drop of dish
soap.  Lightly spray plastic and squeegee fluid out following the above technique. Sit in sun (inside a car window
makes for a good solar oven)  or heat lightly with hair dryer, avoid over heating. Avoid using for 24 hours You
may trim edges with a razor blade.

Gas tanks: (Make sure you remove the little hole plugs before installing). Empty and clean gas tanks of all gasoline
and let sit for 3-4 days. Install graphic do not apply wet.  Once installed let graphic sit for 48 hours before putting gas in
tank.  Air bubbles will occur after use push air out of the holes to lay flat.  (Gas will dissolve the glue over a period of time
we do not guarantee the decal on gas tanks.) Lastly do not store your bike with gas in the tank and unscrew the tank cap.
this applies to: PW50 YZ85 YZ125/250 RM85 RM125/250 and other older bikes that have exposed tanks.
Reprints are available for the gas tank pieces at:

This is a classic video of a mechanic having to deal with a dude videoing him.  We had this happen to more
then once, "trying to be nice but I got to get stuff done":)

Remember be patient!!!!!!!!!!!

Trailer Graphic Instructions

1 Patients is the key to success!!!!!!!!!!!!!!!!!!!!

2 Find a big table and layout all the pieces. Each piece is numbered
(if done in cut vinyl) by the order it should be put on.

3 This graphic is big so the best way to put this on is wet. Have a sprayer
bottle  (NO Windex or window cleaners) with 2 drops of dish soap to 16oz of
water and a squeegee (small 6inch window one will do.)

4 Figure out the area on the trailer you want to do and clean really good and
remove any screws which could be in the graphic area.

5 Mask a straight line and make sure it level. This will give you a good reference.
Don't try and eyeball it.

6 Lightly mist the area you will be applying then peel and wet back fo decal with
fluid lightly. Apply by starting in one corner and squeeze the air bubbles out as you go.
The wet back will help this. Then move on to piece #2 and so on. If this graphic is
done in pieces, seams are made to over lap by about a 1/4 inch.

7 Once you have all the decals go away for a  few hours and let dry. Let vehicle
sit in the sun the any air bubbles will out gas.  Some will remain you can pop those
with an Exacto knife.  Also over time most bubbles perk out.


Contact Us
    FAQS   Shipping    Instructions

facebook  insta
(970)759-0411 sales@ruskracing.com
©2002-2021 Rusk Racing

Established 2002